Kyber Developers (@KyberDeveloper) — Telegram group messages

Hello colleagues. I want to run Solana, but I don't understand what to send for the swap info request. If I send abi and the address of the token to polygon, then I send the same to solana? where to look abi, is there an analogue of polygonscan for solan?

05:54

I
id 5850853853
Solana is different, there are nothing like abi, in solana ypu create a program and request lamport to run it
06:46
1. S
  Sergey Sarafinovich
  I'm sorry, I did not understand you. what exactly needs to be done? do you have a link to the documentation where it says what i should send?
  02:09

Whole thread · 2 replies →

1 July 2023

id 5850853853

hi @Ivan_ser123 here's the doc https://docs.kyberswap.com/kyberswap-solutions/kyberswap-aggregator/aggregator-api-specification/solana-swaps, you can check the example here https://github.com/KyberNetwork/kyberswap-interface/blob/main/src/utils/aggregator.ts#L396-L568

03:05

id 5850853853

note that for solana, you need to understand what's larmport, program, pair... first

03:05

2 July 2023

Li cy

Photo
click to show

so, what's mean route_service for solana ? where i can get?

04:22

I
id 5850853853
this one https://aggregator-api.kyberswap.com/solana/route/encode
04:39

Whole thread · 1 reply →

Li cy

thanks

04:57

hello, have a question about kyber elastic swap function. i deployed IPoolActions interface at the address of a WETH-USDT pool on Arbitrum. CA here: 0xdb0f89c3aEb216d4329985442039F3737CBFc949 When i call the swap function with correct inputs, it doesn't return me anything at all. which is incorrect with what the function specs here on the site. I'm not even sure if the interface is being deployed correctly since I can call the swap function without even needing to approve the token first. What am I doing wrongly? can someone help pls 🙏🙏

09:58

I
id 5850853853
the swap() function will not return anything, you can have success or failed only. also, if your wallet already approve/permit token with kyberswap contract then you don't need to do that again
10:30
1. J
  JY
  hey nick, thank you for replying. really appreciate it. this is the function I'm talking about: https://arbiscan.io/token/0xdb0f89c3aEb216d4329985442039F3737CBFc949#writeContract#F8 I'm trying to swap WETH-USDC based on this instructions: https://docs.kyberswap.com/liquidity-solutions/kyberswap-elastic/developer-guides/execute-an-elastic-swap I've approved the contract to spend my WETH. I've tried doing it through the arbiscan UI on Arbitrum mainnet, and through a fork on Hardhat and either the transaction gets reverted or the gas amount shown is insanely high. Any idea what I'm doing wrongly? am using the MIN_SQ_RATIO + 1 for the sqrtlimitp
  15:56
  1. I
    id 5850853853
    how much gas you put into swap()?
    05:09
    1. J
      JY
      i didn't make any special changes to gas limits or gas fees. left it as it is. Do we have to pass something into the data parameter? I realized that when it does the token transfers, swapcallback actually uses data, but I've just been passing data in as bytes memory data = new bytes(0);
      08:10
      1. J
        JY
        ok no worries i implemented it through the router instead. Just wanted to feedback that the documentation here could be clearer in explaining how to directly swap from a single pool! https://docs.kyberswap.com/liquidity-solutions/kyberswap-elastic/developer-guides/execute-an-elastic-swap no idea what to pass in to the data parameter if we called swap() on the pool directly
        09:41

Whole thread · 5 replies →